search

Jensen-heavy-duty JHDATVK Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour bateaux Jensen-heavy-duty JHDATVK. Jensen Heavy Duty JHDATVK User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 4
  • Table des matières
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
JHDRMT - Rack Mount for the JENSEN MINI Radio
MOUNTING THE RACK CLAMP:
1. Remove the 2 Clamp Bolts, using the supplied 5/32” hex key, separate the clamp and place the bottom half under the rack where
you want to locate the mount on the rack.
2. Place the top half of the clamp on the rack and install the Clamp Bolts. Tighten until you cannot move the clamp assembly.
TOP PLATE: The top plate of the JHDRMT can be mounted using any one of the three mounting holes across the top of the plate, for added exibility.
The mount comes fully assembled utilizing the center mounting hole and may not need to be changed. This will depend on the location you chose to attach
the mount to the rack and where you want the radio to be placed.
To adjust the angle of the Top Plate:
1. Slightly loosen the three Small Silver Set Screws in the Ball-Socket under the Top Plate, using the supplied 1/8” Hex Key.
2. Position the Top Plate to the desired angle and then re-tighten all three equally.
To lock the ball in place, tighten the Black Set Screw. To move or adjust the angle again, the Black Set Screw must be loosened.
BASE PIVOT:
The Base Pivot can be turned to any direction needed.
1. Remove the Shaft Bolt holding the Shaft onto the Base Pivot using the supplied 3/16” hex key. Lift the Shaft straight out.
This allows access to the 1/8” Base Pivot Bolt inside the Base Pivot.
2. Loosen the Base Pivot Bolt using the supplied 1/8” hex key enough to lift the Base Pivot and clear the locking pin on the top of the clamp.
Turn to the desired location and make sure that the locking pin is in one of the locking holes on the bottom of the Base Pivot before tightening
the Base Pivot Bolt.
MOUNT RADIO: At this point you should be able to determine the position of the Top Plate. Once you are satised that you have positioned the mount
exactly where you want it, it is time to mount the JHD MINI radio.
1. Using the 4 M4 machine screws that were included with the JHD MINI, attach the radio to the Top Plate matching up the 4 holes on the back
of the radio to the 4 holes on the top Plate (AMPS Pattern).
Complete the radio installation per the instructions included with the JENSEN JHD MINI Radio. Contact the vehicle manufacturer for advice regarding
the best location for Power and Ground connections.
37200042 REV-A
JHDATVK
Installation Instructions
Page 1-2
Vue de la page 0
1 2 3 4

Résumé du contenu

Page 1 - Installation Instructions

JHDRMT - Rack Mount for the JENSEN MINI RadioMOUNTING THE RACK CLAMP:1. Remove the 2 Clamp Bolts, using the supplied 5/32” hex key, separate the clamp

Page 2 - WARNING:

RACK MOUNT PART #JHDATVK INCLUDES:(1) JHDRMT(1) JXHDARMT(1) JXHDRMT(1) 3/16” Hex Key(1) 5/32” Hex Key(1) 1/8” Hex Key LIMITED WARRANTY

Page 3

JXHDARMT - Rack Mount for the JENSEN JXHD35 Speaker and JAN139 Antenna1. MOUNTING THE SPEAKER BRACKET:Attach the Speaker Bracket to the Mounting Plate

Page 4

RACK MOUNT PART #JHDATVK INCLUDES:(1) JHDRMT(1) JXHDARMT(1) JXHDRMT(1) 3/16” Hex Key(1) 5/32” Hex Key(1) 1/8” Hex Key LIMITED WARRANTY

Commentaires sur ces manuels

Pas de commentaire
  • AMEC Eppendorf STC Ibiza Sound Ameri-King
  • Olympus Multifonctionnels Microsoft Logiciel VisionTek Cartes graphiques Amtrol Pompes à eau Dualit Bouilloires électriques
  • Sony MEX-BT3900U Yamaha RX-V863 Sekonic MULTIMASTER L-408 Brother HL-5450DNT Casio EX-JE10
  • Samsung VP-D371W Manuel de l'utilisateur AEG HK854420XB Manuel de l'utilisateur Sony CXS-GT46F Manuel de l'utilisateur Sony NWZ-A728 Manuel de l'utilisateur